loading_img

ten percent fines value of aggregate for astm

AGGREGATE CRUSHING VALUE AND TEN PERCENT FINES VALUE …

Aggregate crushing Value provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Ten Percent Fines Value used for testing aggregate smaller than 10 mm. Comprises: 150 mm or 75mm diameter steel cylinder, plunger, base plate, tamping rod and metal measure. More +.

ASTM International - ASTM D2419-14 - Standard Test Method ...

Jun 01, 2014· Note 1: For fine aggregates containing clean dust of fracture (clay-size particles that are not clay minerals), test results will depend on the amount of fines present in the material. In this case other tests such as Methylene Blue Value (AASHTO T330) or X-Ray Diffraction (XRD) may be needed to determine if the fines are deleterious.

Test 1 : Standard Slump and Flow Table Tests

To determine the reference slump value for Kistner concrete mix design and to calibrate it against an equivalent measure using a flow table. Materials Natural coarse aggregate and siliceous fine aggregate with maximum size of 3/8 in., supplied by Kistner Concrete Products, Inc. Soda-lime glass aggregate passing #4 standard sieve.

APPLICATION OF PUMICE AGGREGATE IN STRUCTURAL …

Ten percent fines value, KN Clay lumps, % Lightweight fine aggregate 12 2135 9.5 2080 1114 - 0.59 Lightweight ... ASTM C330 Lightweight fine aggregate Natural sand Figure 2. Lightweight fine ...

AGGREGATE BLENDING, ABSORPTION, & SPECIFIC GRAVITY

Aggregate Blending, Absorption & Specific Gravity 15 Fine Aggregate Specific Gravity • ASTM C128 – Dry aggregate – Soak in water for 24 hours – Spread out and dry to SSD – Add 500 g of SSD aggregate to pycnometer of known volume • Pre-filled with some water – Add more water and agitate until air bubbles have been removed

Aggregates for Use In Concrete

Fine Aggregate Gradation • Fineness Modulus (FM) should be between 2.3 and 3.1 Sieve Percent Passing ASTM C 33 Grading for Fine Agg • FM is empirical # determined by dividing the sum of percent retained on a standard series of sieves by 100 (No. 4, 8, 16, 30, 50, 3/8 in 100 No. 4 95-100 No. 8 80-100 No. 16 50-85 100) • Coarser fine aggregate

Evaluation of Fine Aggregate Morphology by Image Method ...

May 29, 2018· The fine aggregates used in this study were nine types in total: 0.6–1.18, 1.18–2.36, and 2.36–4.75; three grades for each type of aggregate. The basic performance indicators of fine aggregates are shown in Table 1.

IS 2386-4 (1963): Methods of test for aggregates for ...

NOTE 1 -The 'aggregate crushing value' gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre- gate of 'aggregate crushing value' 30 or higher, the result may be anomalous, and in such cases the 'ten percent fines value' should be determined instead.

FLAT PARTICLES, ELONGATED PARTICLES, OR FLAT AND …

IN COARSE AGGREGATE ASTM D 4791 GLOSSARY Flat and Elongated Particles of Aggregate - Those particles having a ratio of length to thickness greater than a specified value. Length - the maximum dimension. Thickness - the maximum dimension perpendicular to the length and width.

Determination Of Ten Percent Fines Value - Help The Engineer

Ten percent fines value is defined as the load taken by the soaked sample at ten percent of fines. Standard Compression Testing Machine. A cylindrical metal measure having an internal diameter of 57 ± 1 mm and an internal depth of 90 ± 1mm. Steel cylinder open ended with plunger and base plate with a normal internal diameter of 75mm.

What is the significance of ten percent fines value in ...

Ten percent fines value is a measure of the resistance of aggregate crushing subjected to loading and it is applicable to both weak and strong aggregate. Fine aggregates are defined as those passing 2.36mm sieve. The test aims at looking for the forces required to produce 10% of fine values (i.e. weight of fines aggregates/weight […]

Aggregates for Concrete - Memphis

(specific gravity) fine aggregate ASTM C 128 (AASHTO T 84) coarse aggregate Absorption and surface Control of concrete quality ASTM C 70 — moisture (water-cement ratio) ASTM C 127 (AASHTO T 85) ASTM C 128 (AASHTO T 84) ASTM C 566 (AASHTO T 255) Compressive and flexural Acceptability of fine ASTM C 39 (AASHTO T 22) Strength to exceed 95% of

Aggregates for Use In Concrete

Fine Aggregate Gradation • Fineness Modulus (FM) should be between 2.3 and 3.1 • FM is empirical # determined by dividing the sum of percent retained on a standard series of sieves by 100 (No. 4, 8, 16, 30, 50, 100) • Coarser fine aggregate has a higher FM Sieve Percent Passing 3/8 in 100 No. 4 95-100 No. 8 80-100 No. 16 50-85

SPECIFIC GRAVITY AND ABSORPTION OF FINE AGGREGATES …

Lightly tamp the fine aggregate into the mold with 25 light drops of the tamper (Figure 3). Each drop should start about 1/5 in. above the top surface of the fine aggregate. Remove loose sand from base and carefully lift the mold vertically. If surface moisture is still present, the fine aggregate will retain the molded shape. When the sand ...

Aggregate Crushing Value Test - Procedure And Result ...

The crushed aggregate sample which is finer than 2.36 mm is separated and expressed as a percentage of the original weight taken in the mould. The percentage of weight passed through the 2.36m IS sieve is known as Aggregate crushing value.. In situations, when the aggregate value 30 or higher the result may be a mistake and in such cases, the "ten percent fines value" should be determined ...

Representative Acceptable Permeability Permeability Range ...

GW Rounded clean well graded gravel 400 >10 GP Pearock, ASTM C33 fine aggregate size 8, MNDOT 3127 FA-3 16000 >10 Coarse limit of ASTM D448 Size No. 78 gravel 24 Fine limit of ASTM D448 Size No. 78 gravel 13 ... -10-3 Silty gravel with more than 30% fines 0.14 SM Silty sand with less than 15% fines 2.13 Silty sand with 15 to 30% fines 0.71 102-10-3

How to determine 10 per cent fines value of aggregate ...

Sep 13, 2018· This video (Animation, Animated Video) explains how to determine 10 per cent fines value of aggregate (Aggregate Test). Aggregate test || Coarse aggregate Te...

CE 354 Transportation Engineering Sessional I (Lab Manual)

checking the mechanical properties (Aggregate Impact Value, Aggregate Crushing Value, and Ten Percent Fines Value), and shape characteristics (Flakiness Index, Elongation Index and Angularity Number) of aggregates used in roadway construction. The test procedures are described as per BS: 812:1975 (PART 1, 2, 3) standards.

ASTM D2419 - 14 Standard Test Method for Sand Equivalent ...

DOI: 10.1520/D2419-14. Citation Format. ASTM D2419-14, Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate, ASTM International, West Conshohocken, PA, 2014, Back to Top

(PDF) Assessment of Fine Aggregates from Different Sources ...

ASTM C 125 as aggregate having bulk density ranging fr om . ... (ACV), aggregate abrasion value (AAV), 10% fines value and petrographical analysis adopting British Standard (BS) testing methods. ...

Aggregates for Concrete as per American Standards - ASTM ...

Fig 1: Aggregates used in production of concrete. The aggregates are broadly classified into two types based on the size, namely- fine aggregate and coarse aggregate. In this article, we discuss the properties of the standard aggregates used in the production of concrete as per the American Standards (ASTM- C33/C33M).

Determination of aggregate impact value and ten percent ...

ILT CODE: ILT-U-1605 Description: Aggregate Impact Value AIV (Dry): Aggregate Impact Value AIV (Wet); Ten Percent fine value TFV (Dry); and Ten Percent fine value TFV (Wet) Method: BS 812 Part 111, BS 812 Part 112

Astm Aggregate Crushing Value Bangladesh

Aggregate Crushing Value Test Astm Pdf. AGGREGATE CRUSHING VALUE 1 Objective The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load With aggregate of aggregate crushing value 30 or higher the result may be anomalous and in such cases the ten percent fines value should be determined …

Standard Test Method for Aggregate Durability Index

the durability index of the aggregate based upon the grading of the aggregate as determined in 9.4. 9.5.1 If less than 10 % of the aggregate passes the No. 4 (4.75-mm) sieve, test coarse aggregate (Procedure A) only. 9.5.2 If less than 10 % of the aggregate is coarser than the No. 4 (4.75-mm) sieve, test fine aggregate (Procedure B) only.

List of Test Methods for Concrete Aggregates

Fine aggregates = 3.0% max. Coarse aggregates = 5.0% max. for structural & pavement concrete; 10.0% max for other classes of concrete. 4. Abrasion Loss (ASTM C-131, C-535) Measures the extent of degradation of coarse aggregates using the Los Angeles Abrasion Machine.

01 03 Aggregate 10% Fines Value - Saliergeotechnical

to calculate the load required to produce 10% fines. Force required to produce 10% fines = 14 x X y + 4 where X and y are as above. 3. Reporting of Results 3.1 Calculate the mean of the two results to the nearest 10kN for forces of 100kN or more, or to the nearest 5kN for forces of less than 100kN. Report the mean as the 10% Fines Value, unless the

Aggregate Ten Percent Fine Value, Mechanical Properties of ...

Aggregate 'Ten Percent Fine Value' (TPFV): The other way of representing the strength of aggregate is the 'ten percent fine value' (TPFV), that is basically the load needed for 10% fines. As compared to aggregate crushing value test this test is more reliable for representing the strength of aggregate.

Optimization of Gradation and Fineness Modulus of ...

Jan 01, 2016· The ASTM limits of gradation and standard value of fineness modulus for sand to be used as fine aggregate in concreting works were being followed for the optimization program. It was evident from the results that S-6 and S-8 satisfy the ASTM standards so the remaining six sands were considered for optimization process. 5.1.

(PDF) Standard Test Method for Effect of Organic ...

Basis for Comparison 2.1 ASTM Standards: 4.1 The fine aggregate shall be compared in mortar, as C 33 Specification for Concrete Aggregates2 described in this test method, with a sample of the same C 40 Test Method for Organic Impurities in Fine Aggre- aggregate that has been washed in a 3 % solution of sodium gates for Concrete2 hydroxide ...

RELATIONSHIP BETWEEN AGGREGATE CRUSHING VALUE …

journal of engineering and technology (jet), vol.6 &2, pp.126-131. relationship between aggregate crushing value (acv) and ten percent fines value (tfv) for nigerian aggregates

Aggregate Crushing Value (ACV) and Ten Percent Fines Value ...

Aggregate Crushing Value (ACV) and Ten Percent Fines Value (TFV) These tests are a measure of the crushing properties of aggregate and use the same basic equipment. The ACV test requires a standard load of 400 kN to be applied over a period of 10 minutes while the TFV test measures the force required to produce a specified depth of plunger ...

Stone Aggregate Testing Laboratory | Sigmatest

10% Fine Value: All aggregates are required to meet a minimum strength valve, as defined by the 10% value test. This and other specifications ensure that only the highest quality materials are being used on construction projects. Test Method: IS: 2386 (P-4)1963. Alkali Aggregate Reactivity:

Astm Code For Aggregate Crushing Value - PRODUSEN ALAT …

Oct 05, 2021· PRODUSEN ALAT LAB TEKNIK SIPIL INDONESIA: alat laboratorium sipil, alat uji laboratorium sipil from analabteknik.weebly.com 1990 methods for determination of ten per cent fines value ( tfv ) Method of prequalification of concrete aggregate: This test is carried out by aashto t 96 or astm c 131: A = iron and steel materials Which is equal to 1 ...

Aggregate Crushing Value and 10% Fines Value.pdf - Chapter ...

Jul 03, 2019· Report the mean as the aggregate 10% fines value, unless the individual results differ by more than 10 kN or by more than 0.1 times the mean value. In this case repeat the test on two further specimens, calculate the median of the four results to the nearest whole number and report the median as the aggregate 10% fines value.

PHYSICAL PROPERTIES OF AGGREGATES

Physical Properties of Aggregates 10 Fine Aggregate ... The study identified a minimum FAA value of 43.3% to resist rutting. Physical Properties of Aggregates 21 Flat, Elongated Particles • Measured on + 4.75 mm material • Based on dimensional ratio of particles –ratio of …

Water absorption of fine recycled aggregates: effective ...

Sep 21, 2018· ASTM C-128-01, Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate, ASTM 36. Tam VWY, Gao XF, Tam CM, Chan CH (2008) New approach in measuring water absorption of recycled aggregates.

determination ten percent fines value aggregate

May 13, 2018· Determination of ten percent fine. THE DETERMINATION OF THE 10 PER CENT FINES AGGREGATE CRUSHING VALUE 1 SCOPE The 10 per cent Fines Aggregate Crushing Value (10 % FACT) as defined hereunder is determined by measuring the load required to crush a prepared aggregate sample to give 10 per cent material passing a specified sieve after crushing.

Organic Impurities in Fine Aggregates for Concrete

Organic Impurities in Fine Aggregates for Concrete ASTM C40/C40M - 19 Page 2 of 2 9.3 Stopper the bottle, shake vigorously, and then allow to stand for 24 h..... 10. Determination of Color Value 10.1 Standard Color Solution Procedure—At the end of the 24-h standing period, fill a glass bottle to the

AGGREGATE 10% FINES VALUE (IS:2386-Part 4-1963 ...

to calculate the load required to produce 10% fines. Force required to produce 10% fines = 14 x X y + 4 where X and y are as above. 3. Reporting of Results 3.1 Calculate the mean of the two results to the nearest 10kN for forces of 100kN or more, or to the nearest 5kN for forces of less than 100kN. Report the mean as the 10% Fines Value, unless the

Our office time Mon - Sat 10.00AM - 7.00PM Sunday CLOSED